Surfaces > Multi-Surface Blend > Freeform Blend
 
 
 

Previously called Freeform fillet, Freeform Blend enables you to create a transitional surface based on two input contact lines.

Freeform Blend Control

Side 1 Continuity/Side 2 Continuity

Choose Position, Tangent, G2 curvature or G3 curvature to determine the type of continuity that will be used between the blend surfaces and primary surfaces. The continuity settings can be specified independently along both sets of boundaries.

G2 curvature continuity means that the curvature (which is the inverse of the radius of curvature) is the same on both sides across the blend surfaces’s boundaries.The V degree of the blend surface is adjusted so that the surface has enough CVs to provide the required continuity on both sides. Degree 4 is needed for G2 continuity on one side, and degree 5 is needed for G2 continuity on both sides

G3 curvature continuity means that the curvature’s rate of change is the same on both sides across the blend surfaces’s boundaries. The V degree of the blend surface is adjusted so that the surface has enough CVs to provide the required continuity on both sides. Degree 6 is needed for G3 continuity on one side, and degree 7 is needed for G3 continuity on both sides.

Lock Shape Controls

When this option is checked on, the values of Side 1 Shape and Side 2 Shape are kept the same.

Side 1 Shape

Provides control over the “looseness” or “tightness” of the blend surface toward the first boundary. If the value is greater than 1.0, the result is a blend that fits tighter to the corner of the input surfaces; if the value is less than 1.0, the result is a rounder blend that fits closer to the edge of the first surface.

Side 2 Shape

Provides control over the “looseness” or “tightness” of the blend surface toward the second boundary. If the value is greater than 1.0, the result is a blend that fits tighter to the corner of the input surfaces; if the value is less than 1.0, the result is a rounder blend that fits closer to the edge of the second surface.

Surface Type

If you choose Single surface, a single blend surface is built. If you choose Multiple surfaces, multiple surfaces, corresponding to the boundaries between the original surfaces, are created. (Extra spans are added, if necessary, to meet tangent or curvature requirements.) This gives you much lighter blend surfaces and better continuity with the original surfaces.

Short Edge Tolerance

In the case of cross-knot insertion, the system will not allow spans of a linear distance less than the Short Edge Tolerance.

Bézier Surfaces

This option only appears if Surface Type is set to Multiple surfaces. If it is checked on, each surface will be a Bézier patch.

Bézier patches have a single span, and their maximum degree in the U direction is set through the Explicit Control section. The default is degree 5.

Explicit Control

Gives you controls of the surface degree and maximum number of spans in the new blend surface.

Explicit Control Options

These options are only available when Explicit Control is checked.

U Degree

The degree of the new blend surface. Enter a whole number from 2 to 9.

Max. Spans

If Surface Type is set to Multiple surfaces, this value specifies the maximum number of spans for each blend surface. If Surface Type is set to Single surface, it specifies the maximum number of spans inside each pair of boundaries between the original surfaces.

This option is only available when Explicit Control is checked, and Bézier Surfaces is not checked.

Flow Control

Start/Interior/End

Controls how the blend surface(s) edges (in the V direction) meet up with the edges of the boundary surfaces.

Edge align – The tool tries to colinearly align the blend surfaces’ edges or isoparms (for single surface) to the edges of the boundary surfaces in the V direction.

Connect ends – The edges of the blend surfaces meet the start and/or end points of the boundaries exactly.

Default or Free – The edges of the blend surface(s) (in the V direction) meet the boundaries at a 90 degree angle.

Control Options

Chain Select

If this box is checked, selecting a boundary input curve also selects all other boundary curves that are tangent continuous with it.

Continuity Check

Displays a manipulator indicating continuity achieved with the existing surfaces along the blend surface edges.

Auto Recalc.

Automatically updates the blend surface as you change options. If the surface to be built is very complex and takes a long time to update, turn this option off and click the Recalc button when you want to update the surface.

See Also