This node is created when you
create a toon line modifier. For more information, as well as illustrations,
see
Use a modifier to alter toon line and brush attributes.
Below are descriptions of the attributes in the lineModifier node.
NoteYou can have multiple line modifier nodes
on a toon line.
Line Modifier Attributes
- Shape
-
Determines the shape of the line modifier. There will
be no effect outside the bounds of the selected shape. The Dropoff graph
attribute is defined relative to the shape, such that the right edge
of the dropoff is the outer edge of the shape, and the left is the
shape’s center.
- Width Scale
-
Multiplies the current line width. A value of
1.0 will have no effect and a value of zero will scale the width
to zero.
- Width Offset
-
Adds on to the current line width. A value of
0.0 will have no effect and a value of 1.0 will increase the width
by one.
- Opacity Scale
-
Multiplies the current line opacity. A value
of 1.0 will have no effect and a value of zero will scale the opacity
to zero.
- Opacity Offset
-
Adds on to the current line opacity. A value
of 0.0 will have no effect and a value of 1.0 will make the lines
fully opaque.
- Surface Offset
-
Adds on to the current line surface offset.
A value of 0.0 will have no effect and a value of 1.0 will increase
the offset by 1.0. Negative values will clamp when an offset of
0 is achieved.
- Line Extend
-
Adds on to the current line extend. A value
of 0.0 will have no effect and a value of 1.0 will increase the
extend by 1.0. Negative values will clamp when an extend of 0 is
achieved.
- Modify Color
-
If this option is turned on, the color value
is blended with the line color based on the dropoff value.
- Color
-
If Modify Color is
turned on, then this color is blended into the local line color
based on the dropoff value.
- Dropoff
-
Dropoff is the loss of individual
leaves, twigs, flowers, tubes, and so on—either a few or
many, depending on the Dropoff settings
you specify.
This setting determines the range of effect within
the bounds of the modifier. If the dropoff is set to a constant
value of 1.0 (horizontal line) then lines will be uniformly modified
inside the bounds of the dropoff shape, with a hard transition at
the shape edge. If the right edge of the dropoff is instead ramped
down to zero the transition will be gradual, with no modulation at
the shape edge, with increasing modulation towards its center. The
dropoff graph attribute is defined relative to the shape, such that
the right edge of the dropoff is the outer edge of the shape, and
the left is the shape’s center.
- Dropoff Noise
-
Modulates the dropoff value with a 3D noise. This
can provide variation for the parameters being modulated. For example
the tube width can be randomized or wiggled in a noisy fashion using
this attribute.
- Noise Frequency
-
Controls how detailed the Dropoff
Noise is. Lower values result in a smoother noise. The
3D noise is defined relative to the local space of the line modifier
shape.
Brush Tube Attributes
For these settings to have any effect, they
require a Paint Effects brush to be used
with tubes turned on.
- Force
-
Acts as a force pushing tubes away from the center
of the line modifier shape. Positive values will push away from
the center while negative values will push towards the center. To
have an effect this requires that a brush be used with tubes turned
on. For example, use this to push Paint Effects trees
as if with the wind.
- Directional Force
-
Acts as a force pushing tubes along the local
x axis of the line modifier shape. To have an effect this requires
that a brush be used with tubes turned on.
- Displacement
-
Acts as a displacement pushing tubes away from the
center of the line modifier shape. Positive values will push away
from the center while negative values will push towards the center. This
is similar to the force attribute, but tube segments further down
the tube are not affected by the offset. To have an effect this
requires that a brush be used with tubes turned on.
- Directional Displacement
-
Acts as a displacement pushing tubes along the local
axis of the line modifier shape. To have an effect this requires
that a brush be used with tubes turned on. This is similar to the
directional force attribute, but tube segments further down the
tube are not affected by the offset.
- Tube Scale
-
Scales the length and width of generated Paint Effects tubes.
A value of 1.0 will have no effect and a value of 0.0 will scale
the tubes to nothing, resulting in no tubes generated. The behavior
is similar to modifying the brush’s Global Scale.
To have an effect this requires that a brush be used with tubes
turned on.
- Tube Dropout
-
Reduces the number of Paint Effects tubes generated.
A value of 0.0 will have no effect and a value of 1.0 will result
in no tubes generated. To have an effect this requires that a brush
be used with tubes turned on.
- Leaf Scale
-
Multiplies the size of leaves used by the Paint Effects brush.
A value of 1.0 will have no effect and a value of 0.5 will reduce
leaf size by half. To have an effect this requires that a brush
be used with tubes turned on.
- Leaf Dropout
-
Adds on to the current leaf dropout value used by
the Paint Effects brush. A value
of 0.0 will have no effect and a value of 1.0 will increase the
dropout by 1.0. To have an effect this requires that a brush be
used with tubes turned on.
- Flower Scale
-
Multiplies the size of flowers used by the Paint Effects brush.
A value of 1.0 will have no effect and a value of 0.5 will reduce
flower size by half. To have an effect this requires that a brush
be used with tubes turned on.
- Flower Dropout
-
Adds on to the current flower dropout value used
by the Paint Effects brush. A value
of 0.0 will have no effect and a value of 1.0 will increase the
dropout by 1.0. To have an effect this requires that a brush be
used with tubes turned on.
- Branch Dropout
-
Adds on to the current branch dropout value used
by the Paint Effects brush. A value
of 0.0 will have no effect and a value of 1.0 will increase the
dropout by 1.0. To have an effect this requires that a brush be
used with tubes turned on.
- Twig Dropout
-
Adds on to the current branch dropout value used
by the Paint Effects brush. A value
of 0.0 will have no effect and a value of 1.0 will increase the
dropout by 1.0. To have an effect this requires that a brush be
used with tubes turned on.