pymel.core.animation.boneLattice

boneLattice(*args, **kwargs)

This command creates/edits/queries a boneLattice deformer. The name of the created/edited object is returned. Usually you would make use of this functionality through the higher level flexor command.

Flags:

• after : af (bool) [create,edit]

  If the default behavior for insertion/appending into/onto the existing chain is not what you want then you can use this flag to force the command to stick the deformer node after the selected node in the chain even if a new geometry shape has to be created in order to do so. Works in create mode (and edit mode if the deformer has no geometry added yet).

• before : bf (bool) [create,edit]

  If the default behavior for insertion/appending into/onto the existing chain is not what you want then you can use this flag to force the command to stick the deformer node before the selected node in the chain even if a new geometry shape has to be created in order to do so. Works in create mode (and edit mode if the deformer has no geometry added yet).

• bicep : bi (float) [create,query,edit]

  Affects the bulging of lattice points on the inside of the bend. Positive/negative values cause the points to bulge outwards/inwards. Default value is 0.0. When queried, this flag returns a float.

• deformerTools : dt (bool) [query]

  Returns the name of the deformer tool objects (if any) as string string ...

• exclusive : ex (unicode) [create,query]

  Puts the deformation set in a deform partition.

• frontOfChain : foc (bool) [create,edit]

  This command is used to specify that the new deformer node should be placed ahead (upstream) of existing deformer and skin nodes in the shape’s history (but not ahead of existing tweak nodes). The input to the deformer will be the upstream shape rather than the visible downstream shape, so the behavior of this flag is the most intuitive if the downstream deformers are in their reset (hasNoEffect) position when the new deformer is added. Works in create mode (and edit mode if the deformer has no geometry added yet).

• geometry : g (unicode) [query,edit]

  The specified object will be added to the list of objects being deformed by this deformer object, unless the -rm flag is also specified. When queried, this flag returns string string string ...

• ignoreSelected : ignoreSelected (bool) [create]

  Tells the command to not deform objects on the current selection list

• joint : j (unicode) [create,query,edit]

  Specifies which joint will be used to drive the bulging behaviors.

• lengthIn : li (float) [create,query,edit]

  Affects the location of lattice points along the upper half of the bone. Positive/negative values cause the points to move away/towards the center of the bone. Changing this parameter also modifies the regions affected by the creasing, rounding and width parameters. Default value is 0.0. When queried, this flag returns a float.

• lengthOut : lo (float) [create,query,edit]

  Affects the location of lattice points along the lower half of the bone. Positive/negative values cause the points to move away/towards the center of the bone. Changing this parameter also modifies the regions affected by the creasing, rounding and width parameters. Default value is 0.0. When queried, this flag returns a float.

• name : n (unicode) [create]

  Used to specify the name of the node being created

• parallel : par (bool) [create,edit]

  Inserts the new deformer in a parallel chain to any existing deformers in the history of the object. A blendShape is inserted to blend the parallel results together. Works in create mode (and edit mode if the deformer has no geometry added yet).

• prune : pr (bool) [edit]

  Removes any points not being deformed by the deformer in its current configuration from the deformer set.

• remove : rm (bool) [edit]

  Specifies that objects listed after the -g flag should be removed from this deformer.

• split : sp (bool) [create,edit]

  Branches off a new chain in the dependency graph instead of inserting/appending the deformer into/onto an existing chain. Works in create mode (and edit mode if the deformer has no geometry added yet).

• transform : t (unicode) [create]

  Specifies which dag node is being used to rigidly transform the lattice which this node is going to deform. If this flag is not specified an identity matrix will be assumed. Flag can have multiple arguments, passed either as a tuple or a list.

• tricep : tr (float) [create,query,edit]

  Affects the bulging of lattice points on the outside of the bend. Positive/negative values cause the points to bulge outwards/inwards. Default value is 0.0. When queried, this flag returns a float.

• widthLeft : wl (float) [create,query,edit]

  Affects the bulging of lattice points on the left side of the bend. Positive/negative values cause the points to bulge outwards/inwards. Default value is 0.0. When queried, this flag returns a float.

• widthRight : wr (float) [create,query,edit]

  Affects the bulging of lattice points on the right side of the bend. Positive/negative values cause the points to bulge outwards/inwards. Default value is 0.0. When queried, this flag returns a float.

Derived from mel command maya.cmds.boneLattice