In this lesson, you will create two cylindrical objects, shape them using polygon edits, then use a union Boolean operation
to add them to the Tower object.
Set up the lesson:
- Continue working on your scene from the previous lesson, or
open \modeling\highrise\building2_tower_contour.max.
Change the size of the upper gap in the highrise:
Maximize the Perspective viewport and zoom in to the gap in the upper section of the tower, as shown in the illustration.
You will bring the back face of the Tower object forward to the midpoint of the structure. To accomplish this, you need to edit the operand that was used to expose
the back face.
Select the Tower object, and in the
Modify panel
Parameters rollout
Display group, choose Operands.
This displays all the box objects, or operands, that were used to modify the Tower object.
- In the list of operands on the Parameters rollout, click to highlight the entry “1: Subtr - Box17”, then turn on
(Select And Move).
The box named Box17 (in building2_tower_contour.max) is the box that was used to make the topmost gap in the tower.
Repositioning the box to the midpoint of the tower involves a simple calculation: at a depth of 30 meters, the tower’s midpoint
is 15 meters. Earlier, you offset the box from the back of the tower by six meters, so it needs to be repositioned to the
left a further nine meters.
- Make sure the coordinate display is set to
relative units (X, Y, and Z spinners all display 0), then in the X field, type –9 , and press Enter.
3ds Max Design moves the box to the left by nine meters.
- On the Parameters rollout
Display group, turn on Result. The back face is now where you want it to be, at the midpoint of the tower.
The next step is to place a cylinder object in the gap between the floors. But rather than create this object at the ground
plane as you did with all other objects in this tutorial, you will create this object directly on the upper platform.
Add the first cylinder to the building:
- On the
Create panel, click
(Geometry), then on the Object Type rollout, click Cylinder. Also, turn on AutoGrid.
With AutoGrid on, you can create the object on top of an object in the scene.
- Click on the center of the upper platform and drag diagonally to set the cylinder radius. Release the mouse button and drag
upwards to set the height, as shown in the next illustration. Click a final time to complete the object. For now, the exact
dimensions are not important.
- Turn off Autogrid.
- Click
(Align), then click the Tower object to display the Align Selection dialog.
- In the Align Position group, turn on X Position and Y Position; make sure Z Position is off. Then choose Center in both the
Current Object and Target Object groups. Click OK.
This aligns the cylinder you just created to the center of the Tower object.
- On the
Modify panel
Parameters rollout, set the parameters of the cylinder as follows:
- Radius = 13.0m
- Height = 30.0m
- Height Segments = 8
- Sides = 20
- Click
(Select And Uniform Scale), and drag the X axis of the gizmo to the right. As you drag the gizmo, the X coordinate spinner
updates dynamically. When the spinner displays a value of 70, stop dragging.
The cylinder shape should now resemble that shown in the next illustration.
Next, you will use some polygon editing techniques to add architectural detail to the cylinder object.
Detail the cylinder: Add windows:
- Click
(Select Object).
- Right-click the cylinder object and choose Isolate Selection from the quad menu.
- Right-click the cylinder object again, and from the Transform (lower-right) quadrant of the quad menu choose Convert To
Convert To Editable Poly.
- On the Selection rollout, click
(Edge),
select any horizontal edge on the cylinder, then click the Ring button.
All horizontal edges above and below the selected edge are also selected.
- Alt+click the top- and bottom-most edges to deselect them.
- Click Loop to select all horizontal edges, excluding the top and bottom rows.
- On the Edit Edges rollout, click the
Settings button to the right of the Chamfer button.
3ds Max Design displays the caddy controls for the Chamfer tool.
- On the Chamfer caddy, change the first control, Edge Chamfer Amount, to 0.6m, then click
(OK).
3ds Max Design changes each horizontal edge loop into a pair of loops 0.6 meters apart.
Detail the cylinder: Bevel the windows:
- On the Selection rollout, click
(Polygon).
- Display the ViewCube if it is not already visible, choose the Left face of the ViewCube, then right-click and choose Orthographic.
NoteIf the ViewCube is not visible in your viewports, from the General viewport label menu (“[+]”) choose ViewCube
![](../images/ac.menuaro.gif)
Show The ViewCube.
- If the orthographic view zooms in too closely, click
(Zoom Extents).
Hold down the Ctrl key, click just outside the cylinder object, and drag across each band created by the chamfer operation, as shown in the
next illustration.
- On the ViewCube, click Home to exit Orthographic view.
- Click
(Zoom Extents) again.
- On the Edit Polygons rollout, click the
Settings button to the right of the Bevel button.
3ds Max Design displays the caddy controls for the Bevel tool.
- On the Bevel caddy, in the first control, choose Local Normal from the drop-down list. In the second control, Height, enter
–1.0, and in the third control, Outline, enter –0.1 to give the edges of the bevel a very slight slope. Click
(OK).
- Click Exit Isolation Mode to redisplay all the scene elements, and on the Selection rollout, click
(Polygon) to exit the Polygon sub-object level.
Place a copy of the cylinder at ground level, and position it:
- Minimize the Perspective viewport to see all four views.
- Zoom so you can see all of the tower.
- Turn on
(Select And Move).
- In the Front viewport, hold down Shift and drag the cylinder on its Y axis to the bottom of the tower.
- In the Clone Options dialog
Object group, turn on Copy, then click OK.
This way, any changes you make to the newly copied object will not affect the upper cylinder.
- Switch the coordinates display to
Absolute Mode and right-click the Z coordinates spinner arrows to position the object at ground level (0.0m).
Move the cylinder to the right on its X axis, until it straddles the back portion of the Tower object, as shown in the next illustration.
TipIf you press F3 to turn on shading and F4 to turn on edged faces, it’s easier to see this.
Scale the new cylinder, and merge the cylinders with the tower:
- Press F3 again to turn off shading.
- Click
(Select And Uniform Scale) and drag the Y axis gizmo upward until the cylinder slightly penetrates the ceiling of the atrium
of the Tower object.
Select the Tower object. On the
Modify panel
Parameters rollout
Operation group, choose Union.
- From the Pick Boolean rollout, click the Start Picking button and select the two cylinder objects to join them to the tower.
- Click the Start Picking button again to turn it off.
Save your work:
- Save the scene as my_building2_cylinders.max.