curve

Go to: Synopsis. Return value. Related. Flags. MEL examples.

Synopsis

curve [-append] [-bezier] [-degree float] [-editPoint linear linear linear] [-knot float] [-objectSpace] [-periodic boolean] [-point linear linear linear] [-pointWeight linear linear linear float] [-replace] [-worldSpace] string

curve is undoable, NOT queryable, and NOT editable.

Return value

Related

Flags

Long name (short name)	Argument types	Properties
-bezier(-bez)
The created curve will be a bezier curve.
-degree(-d)	float
The degree of the new curve. Default is 3. Note that you need (degree+1) curve points to create a visible curve span. eg. you must place 4 points for a degree 3 curve.
-replace(-r)
Replaces an entire existing curve. If you use this flag, you must specify the name of the curve to replace, at the end of the command. (See examples below.)
-append(-a)
Appends point(s) to the end of an existing curve. If you use this flag, you must specify the name of the curve to append to, at the end of the command. (See examples below.)
-point(-p)	linear linear linear
The x, y, z position of a point. "linear" means that this flag can take values with units.
-pointWeight(-pw)	linear linear linear float
The x,y,z and w values of a point, where the w is a weight value. A rational curve will be created if this flag is used. "linear" means that this flag can take values with units.
-editPoint(-ep)	linear linear linear
The x, y, z position of an edit point. "linear" means that this flag can take values with units. This flag can not be used with the -point or the -pointWeight flags.
-knot(-k)	float
A knot value in a knot vector. One flag per knot value. There must be (numberOfPoints + degree - 1) knots and the knot vector must be non-decreasing.
-periodic(-per)	boolean
If on, creates a curve that is periodic. Default is off.
-objectSpace(-os)
Points are in object, or "local" space. This is the default. You cannot specify both "-os" and "-ws" in the same command.
-worldSpace(-ws)
Points are in world space. The default is "-os". You cannot specify both "-os" and "-ws" in the same command.

Flag can appear in Create mode of command	Flag can appear in Edit mode of command
Flag can appear in Query mode of command	Flag can be used more than once in a command.

MEL examples

curve -p 0 0 0 -p 3 5 6 -p 5 6 7 -p 9 9 9;
curve -pw 0 0 0 1 -pw 3 5 6 1 -pw 5 6 7 1 -pw 9 9 9 1;
curve -p 0cm 0cm 0cm -p 3in 5in 6in -p 5ft 6ft 7ft -p 9 9 9;
// These commands create curves with four control vertices.
// The first one is created without weights.  The third command
// shows how you can use units to specify position.
curve -r -p 0 0 0 -p 3 5 6 -p 10 12 14 -p 9 9 9 curve1;
// This command replaces an existing curve, curve1, with the given points.
// Do not use this flag on a curve that is a result of a construction
// history operation.
curve -a -p 13 13 13 -p 13 15 16 curve1;
// This command adds two CVs to an existing curve, curve1.
// The "-ws" flag can be used if the specified CVs are in world space.
// Do not use this flag on a curve that is a result of a construction
// history operation.
curve -p 0 0 0 -p 3 5 6 -p 5 6 7 -p 9 9 9 -p 12 10 2 -k 0 -k 0 -k 0 -k 1 -k 2 -k 2 -k 2;
// This command creates a curve with five control vertices,
// with a knot vector. Notice that there must be
// (number of CVs + degree - 1) knots and that the knot
// vector must be non-decreasing.
curve -per on -p 0 0 0 -p 3 5 6 -p 5 6 7 -p 9 9 9 -p 0 0 0 -p 3 5 6 -p 5 6 7 -k -2 -k -1 -k 0 -k 1 -k 2 -k 3 -k 4 -k 5 -k 6;
// This command creates a closed (or "periodic") curve with
// four distinct CVs. You must specify a knot vector when the
// "-per" flag is used. Notice that the first "degree" points
// are the same as the last "degree" points (ie. the first three
// points are the same as the last three points). Notice also
// that the knot spacing between the first "degree" knots must
// be the same as the spacing between the last "degree" knots
// (ie. the space between the 1st and 2nd knots is the same as
// the space between the 7th and 8th knots, and the space between
// the 2nd and 3rd knots is the same as the space between the
// 8th and 9th knots). There must be space between the first
// "degree" knots, unlike the previous example, where the first
// "degree" knots are the same.
// How to query curve properties:
getAttr "curve1.degree";
// This returns the degree of the curve.  Note that the
// number of CVs = degree + spans.
getAttr "curve1.spans";
// This returns the number of spans in the curve.  Note that the
// number of CVs = degree + spans.
getAttr "curve1.form";
// This returns the curve form.
getAttr "curve1.minValue";
// This returns the minimum parameter value on the curve.
getAttr "curve1.maxValue";
// This returns the maximum parameter value on the curve.
getAttr "curve1.cv[0]";
// This returns the local x,y,z of the 1st CV.  Use a curve info node if
// the curve is a result of a construction history operation.
getAttr "curve1.cv[0:2]";
// This returns the local x,y,z of the 1st three CVs.  Use a curve info
// node if the curve is a result of a construction history operation.
getAttr "curve1.cv[*]";
// This returns the local x,y,z of all CVs.  Use a curve info node if
// the curve is a result of a construction history operation.
arclen curve1;
// This returns the arc length of the curve.  Use "-ch" flag with
// the arclen command to get a curve info node that constantly updates
// to the current arc length.
createNode curveInfo;
connectAttr curveShape1.worldSpace curveInfo1.inputCurve;
getAttr "curveInfo1.knots[*]";
// This sequence creates a curve info node, connects the info node to the
// curve and queries the knot vector of the curve using the curve info node.
// You can use the curve info node to query other attributes such as
// world space CV values and arc length.