Area Shadows Rollout
 
 
 
Command entry: Create panel (Lights) Create a light. General Parameters rollout Shadows group Shadow type Area Shadows Area Shadows rollout
Command entry:Select a light. Modify panel General Parameters rollout Shadows group Shadow type Area Shadows Area Shadows rollout

The Area Shadow generator can be applied to any light type to achieve the effect of an area shadow effect. In order to create an area shadow, the user needs to specify the dimensions of a virtual light created to "fake" an area shadow.

The mental ray renderer does not support Area shadows. When it encounters a light with this shadow type, it generates ray-traced shadows instead, and displays a warning to that effect. While the mental ray renderer does not use the Area shadow type, it can generate area shadows: use a photometric light set to a light shape other than Point. See Shape/Area Shadows Rollout.

NoteWhen you use area lights, try to make the properties of the light match the properties in the Area Light Dimensions group of the Area Shadows rollout.
TipArea shadows can take a fair amount of time to render. If you want to create a quick test (or draft) rendering, you can use the Area/Linear Lights as Point Lights toggle in the Common Parameters rollout of the Render Setup dialog to speed up your rendering. When this toggle is on, the shadows are processed as if the light object is a point source.

Area shadows create a soft edge that becomes more noticeable as the distance between the object and the shadow increases.

A: Penumbra (soft area)

B: Shadow

Area shadow cast by a point light

Interface

Basic Options group

Mode

Selects the way the area shadows are generated:

  • SimpleCasts a single ray from the light toward the surface. No antialiasing or area light calculation is performed.
  • Rectangle LightCasts rays from the light in a rectangular array.
  • Disc LightCasts rays from the light in a circular array.
  • Box LightCasts rays from the light as if it were a box.
  • Sphere LightCasts rays from the light as if it were a sphere.

    The shape of the area shadow array affects how shadows are cast.

    Left: Rectangle

    Right: Box

2-Sided Shadows

When on, backfaces are not ignored when calculating shadows. Objects seen from the inside are not lit by lights from the outside. This costs a bit more render time. When off, backfaces are ignored. Rendering is quicker, but outside lights illuminate object interiors.

The faces inside the sliced sphere do not cast shadows if 2-Sided Shadows is off.

Antialiasing Options group

Shadow Integrity

Sets the number of rays in the initial bundle of rays cast. These rays are projected from every surface that receives light from the light source.

The number of rays is as follows:

1=4 rays

2=5 rays

3 to N=NxN rays.

For example, setting Shadow Integrity to 5 generates 25 rays.

This is the primary control for “finding” small objects and thin spaces between objects. If the shadows are missing a small object in your scene, try increasing Shadow Integrity one step at a time. Also, if the penumbra (soft area) is blotchy, try increasing this setting.

Increasing the Shadow Integrity value creates more accurate shadow contour and detail.

Shadow Quality

Sets the total number of rays cast in the penumbra (soft area) region, including the rays fired in the first pass.

These rays are projected from every point that is in the penumbra, or antialiased edge of the shadow, to smooth it out.

The number of rays is as follows:

  • 2=5 rays
  • 3 to N = NxN

For example, setting Shadow Quality to 5 generates 25 rays.

The Shadow Quality value should always be greater than the Shadow Integrity value. This is because 3ds Max overlays the secondary rays atop the first pass's rays using the same algorithm.

Increase Shadow Quality to fix banding in the penumbra, and eliminate the noise pattern from jittering.

Increasing the Shadow Quality value produces a more accurate penumbra (soft area) within the contour defined by the Shadow Integrity value.

Sample Spread

The radius, in pixels, to blur the antialiased edge.

NoteAs this value increases, so does the quality of the blur. However, increasing this value also increases the likelihood of missing small objects. To avoid this problem, increase the value of Shadow Integrity.
Shadow Bias

Shadow bias is the minimum distance that an object must be from the point being shaded in order to cast a shadow. This prevents blurred shadows from affecting surfaces they shouldn't.

NoteAs you increase the blur value, you should also increase the bias.
Jitter Amount

Adds randomness to the ray positions. The rays are initially in a very regular pattern, which can show up in the blurry part of the shadow as regular artifacts. Jittering will convert these artifacts to noise, which is generally less noticeable to the eye. Recommended values are 0.25 to 1.0. However, very blurry shadows require more jitter.

Increasing jitter blends the individual shadow samples.

Area Light Dimensions group

3ds Max uses these dimensions to compute the area shadowing. They do not affect the actual light object.

Length

Sets the length of the area shadow.

Width

Sets the width of the area shadow.

Height

Sets the height of the area shadow.